Winter 2010 Posters/SheevaPlug Configuration

From CDOT Wiki
Jump to: navigation, search

Project Name

SheevaPlug Configuration

Names

Alex Vlahopoulos

The SheevaPlug Hardware Specifications

Sheeva CPU Core

1.2 GHz operation

L1 Cache: 16K Instruction + 16K Data

L2 Cache: 256KB

Memory

DDR2 400MHz, 16-bit bus

512MB DDR2: 1Gb x8, 4 devices

Power efficient Samsung devices

NAND FLASH Controller, 8-bit bus

512MB NAND FLASH: 4Gb x8, direct boot

128-bit eFuse Memory

Power

Power input: 100-240VAC/50-60Hz 19W DC Consumption: 5V/3.0A High efficiency POL DC-DC converters

Development Interface

System Development Board JTAG and Console Interface via USB SDIO expansion JTAG OpenOCD support via USB

High Speed I/O & Peripherals

GE, USB 2.0 Host RTC w/ Battery

The Goal

The goal of this project was to successfully run Fedora 12 on the SheevaPlug. The operating system that came loaded on the device is Debian. The purpose behind installing Fedora 12 on this device is to test the operating system's performance on the ARM architecture. Further tests will be performed in the future to determine if the SheevaPlug is a good choice for the Fedora Arm Secondary Architecture Project to use a stack of these devices as builders.

Challenges

1. 512MB NAND is too small to install a regular installation of Fedora 12 (The plug has no disk).

2. The plug does not have a BIOS, instead it has a bootloader (U-boot) however this needed to be updated.

3. No video card.

4. Some network configuration had to be made when plugged into my network. This network configuration was required in order to download "wget".

Solutions

1. In order to run Fedora 12 on the SheevaPlug I had to install the operating system on an SD card (although it can also be installed on a USB drive).

2. The bootloader was easily upgradable by accessing the newer version via TFTP or USB from a web source (http://www.cyrius.com/debian/kirkwood/sheevaplug/uboot-upgrade.html)

3. Since the SheevaPlug doesn't have a display adapter, it comes integrated with a built in "serial console to mini USB" connection. The connection can be made to either a Windows or Linux machine. For the purpose of this project, I connected it to a Windows machine.

4. The default gateway had was configured and the name server was added to the resolv.conf file.

Results

1. Fedora 12 was successfully installed on an SD card and booted from the SheevaPlug. The boot up time was quick as well, with minimal extra configuration required once booted it up (i.e. networking).

2. Following the HOW-TO page for upgrading U-boot (located in the Links section) was pretty simple, however making sure the uboot.bin file copies over to the USB drive is important for the device to actually read it and copy it over. To configure U-boot, about 7 configuration commands were required, as soon as this was done and the device rebooted, the device selected the SD card and booted Fedora 12.

3. Once I connected the SheevaPlug with the "mini USB to regular USB" cable, I installed the Windows drivers that came with the CD and using PuTTy I used a serial connection to COM 1 using 115200 as the connection speed in order to connect to the device.

4. Configuring the name server enabled the connection to the Internet and I was able to use apt-get to install "wget". Wget was required to download the Distro and the Kernel for when I had to install Fedora 12 on the SD card.

Acknowledgements

Chris Tyler

Links

Graphics

http://4.bp.blogspot.com/_5jmDGTgbN2E/S7vKZgoEBfI/AAAAAAAAABA/2gdWHrl0pSs/s1600/IMG00066-20100406-1739.jpg

http://www.globalscaletechnologies.com/skins/skin_1/images/Sheeva_Plug_BlockDiagram.png

Logos

  • Fedora
  • Seneca