Difference between revisions of "SPO600 64-bit Assembly Language Lab"

From CDOT Wiki
Jump to: navigation, search
Line 1: Line 1:
 
[[Category:SPO600 Labs]][[Category:Assembly Language]]
 
[[Category:SPO600 Labs]][[Category:Assembly Language]]
  
 +
{{Admon/caution|Not Updated|This page contains outdated information. It will be updated with new information for Fall 2014.}}
 
{{Admon/lab|Purpose of this Lab|In this lab, you will experiment with assembler on the x86_64 and aarch64 platforms.}}
 
{{Admon/lab|Purpose of this Lab|In this lab, you will experiment with assembler on the x86_64 and aarch64 platforms.}}
 
{{Admon/tip|Ireland|Perform this lab on ireland.proximity.on.ca.}}
 
{{Admon/tip|Ireland|Perform this lab on ireland.proximity.on.ca.}}

Revision as of 21:49, 4 September 2014


Stop (medium size).png
Not Updated
This page contains outdated information. It will be updated with new information for Fall 2014.
Lab icon.png
Purpose of this Lab
In this lab, you will experiment with assembler on the x86_64 and aarch64 platforms.
Idea.png
Ireland
Perform this lab on ireland.proximity.on.ca.

Lab 3

Ireland - Configuration

The host Ireland (ireland.proximity.on.ca) has been set up so that you can use it normally as an x86_64 host, or use an emulation environment to build and run aarch64 binaries.

The directory ~/arm64/spo600/examples, which is also accessible as ~/spo600-examples, contains these files:

── hello                         # 'hello world' example programs
   ├── assembler
   │   ├── aarch64               # aarch64 assembler version
   │   │   ├── hello.s
   │   │   └── Makefile
   │   └── x86_64                # x86_64 assembler versions
   │       ├── hello-gas.s       # 64-bit instructions with AT&T/gnu assembler syntax (called 'gas', /usr/bin/as)
   │       ├── hello-nasm.s      # 32-bit instructions with Intel/nasm assembler syntax (/usr/bin/nasm)
   │       └── Makefile
   └── c
       ├── hello2.c              # C version using the write() syscall wrapper
       ├── hello.c               # C version using printf()
       └── Makefile

Throughout this lab, take advantage of make whenever possible.

Group Lab Tasks

1. Build and run the C versions of the program for x86_64.

2. Review, build, and run the x86_64 assembler programs. Make sure you understand the code.

4. Build and run the C versions of the program for aarch64 (note: you may need to make clean). Verify that you can disassemble the object code in the ELF binary using objdump -d

5. Review, build, and run the aarch64 assembler programs. Make sure you understand the code.

6. Here is a basic loop in x86_64 assembler - this loops from 0 to 9, using r15 as the index (loop control) counter:

.text
.globl    _start

start = 0                       /* starting value for the loop index */
max = 10                        /* loop exits when the index hits this number (loop condition is i<max) */

_start:
    mov     $start,%r15         /* loop index */

loop:
    /* ... do something useful here ... */

    inc     %r15                /* increment index */
    cmp     $max,%r15           /* see if we're done */
    jne     loop                /* loop if we're not */

    mov     $0,%rdi             /* exit status */
    mov     $60,%rax            /* syscall sys_exit */
    syscall

Extend this code, combining it with code from the "Hello World" example, so that it prints each digit from 0 to 9 like this:

Loop: 0
Loop: 1
Loop: 2
Loop: 3
Loop: 4
Loop: 5
Loop: 6
Loop: 7
Loop: 8
Loop: 9
Idea.png
Character conversion
In order to print the loop index value, you will need to convert from an integer to digit character. In ASCII/ISO-9959-1/Unicode UTF-8, the digit characters are in the range 48-57 (0x30-0x39). You will also need to assemble the message to be printed for each line - you can do this by writing the digit into the message buffer before outputting it to stdout, or you can perform a sequence of writes for the thee parts of the message ('Loop: ', number, '\n').

7. Repeat step 6 for aarch64.

8. Extend the code to loop from 00-30, printing each value as a 2-digit decimal number.

Idea.png
2-Digit Conversion
You will need to take the loop index and convert it to a 2-digit decimal number by dividing by 10. To do this, use the div instruction, which takes the dividend from rax and the divisor from register supplied as an argument. The quotient will be placed in rax and the remainder will be placed in rdx.

9. Repeat step 8 for aarch64.

Deliverables

1. Complete the group lab section, above.

2. Extend the assembler programs (both x86_64 and aarch64) to suppress the high digit when it is 0. In other words, the printed values should progress from 0-30 instead of from 00-30. It is OK to output a space in place of the suppressed digit (this will cause the numbers to be aligned vertically in the printout).

3. Blog about the programs you've written. Describe the experience of writing and debugging in assembler, as compared to writing in other languages. Contrast x86_64 and aarch64 assembler, your experience with each, and your opinions of each. Include links to the source code for both of your assembler programs.

References