Difference between revisions of "Fedora ARM Secondary Architecture/SheevaPlug"

From CDOT Wiki
Jump to: navigation, search
Line 1: Line 1:
 
[[Category:Fedora ARM Secondary Architecture]][[Category:SBR600]]
 
[[Category:Fedora ARM Secondary Architecture]][[Category:SBR600]]
−
== '''SheevaPlug Specifications''' ==
+
= Goal =
  
−
'''Sheeva CPU Core'''
+
To prepare the SheevaPlug, one of the [[Fedora ARM Secondary Architecture/ARM Hardware|ARM systems]], so that it can be added to the Koji build pool.
  
−
1.2 GHz operation
+
= '''SheevaPlug Specifications''' =
  
−
L1 Cache: 16K Instruction + 16K Data
+
== Sheeva CPU Core ==
 +
* 1.2 GHz operation
 +
* L1 Cache: 16K Instruction + 16K Data
 +
* L2 Cache: 256KB
  
−
L2 Cache: 256KB
+
== Memory ==
 +
* DDR2 400MHz, 16-bit bus, 512MB
 +
* NAND FLASH Controller, 8-bit bus, 512MB NAND FLASH
 +
* 128-bit eFuse Memory (for tiny, permanent storage, e.g., serial number)
  
−
'''Memory'''
+
== Power ==
  
−
DDR2 400MHz, 16-bit bus
+
* Power input: 100-240VAC/50-60Hz 19W DC Consumption: 5V/3.0A
 +
* High efficiency POL DC-DC converters
  
−
512MB DDR2: 1Gb x8, 4 devices
+
== Development Interface ==
  
−
Power efficient Samsung devices
+
* System Development Board JTAG and Console Interface via USB
 +
* SDIO expansion
 +
* JTAG OpenOCD support via USB
  
−
NAND FLASH Controller, 8-bit bus
+
== High Speed I/O & Peripherals ==
 +
* USB 2.0 Host
 +
* SD slot
 +
* RTC w/ Battery
 +
* Programmable LED
  
−
512MB NAND FLASH: 4Gb x8, direct boot
+
== Hardware Links ==
 +
* [http://www.globalscaletechnologies.com/p-22-sheevaplug-dev-kit-us.aspx Manufacturer's product page]
  
−
128-bit eFuse Memory
+
= Accessing SheevaPlug from a Windows 7 box =
−
 
 
−
'''Power '''
 
−
 
 
−
Power input: 100-240VAC/50-60Hz 19W DC Consumption: 5V/3.0A
 
−
High efficiency POL DC-DC converters
 
−
 
 
−
'''Development Interface'''
 
−
 
 
−
System Development Board
 
−
JTAG and Console Interface via USB
 
−
SDIO expansion
 
−
JTAG OpenOCD support via USB
 
−
'''High Speed I/O & Peripherals'''
 
−
 
 
−
GE, USB 2.0 Host
 
−
RTC w/ Battery
 
−
 
 
−
'''<font color="#000000">'''UL/CE/FCC certified'''</font>'''
 
−
 
 
−
 
 
−
 
 
−
[http://www.globalscaletechnologies.com/p-22-sheevaplug-dev-kit-us.aspx For more information]
 
−
 
 
−
== '''Accessing SheevaPlug from a Windows 7 box''' ==
 
−
 
 
−
Step 1:  Connect the device using the mini USB -> USB cable.
 
−
 
 
−
Step 2:  Chances are Windows will struggle to find drivers for the device so just use the SheevaPlug_Host_SWsupportPackageWindowsHost.zip file that is included in the DevKit CD.  Unzip it and use Device Manager to browse for the TeraTerm Drivers (located as a sub directory in the zip file you just extracted).
 
−
 
 
−
Step 3:  Windows will find 2 devices (USB Converter A and B)  A = JTAG port B = serial port.  We want to connect to the serial port.
 
−
 
 
−
Step 4: Click on Port B, select properties and in the Advance tab ensure LOAD VCP is selected.
 
−
 
 
−
Step 5: Unplug the device, and plug it back in.
 
−
 
 
−
Step 6: Using PuTTY, connect to the COM port of "PORT B" and make sure the SPEED is set to 115200.
 
−
 
 
−
Step 7: You might need to press ENTER  once or twice to get the prompt to actually show (sounds silly but it took me a while to figure that out lol).
 
−
 
 
−
Step 8: Login using the default authentication information (username = root ) (password = nosoup4u)
 
  
 +
# Connect the device using the mini USB -> USB cable.
 +
# Chances are Windows will struggle to find drivers for the device so just use the SheevaPlug_Host_SWsupportPackageWindowsHost.zip file that is included in the DevKit CD. Unzip it and use Device Manager to browse for the TeraTerm Drivers (located as a sub directory in the zip file you just extracted).
 +
# Windows will find 2 devices (USB Converter A and B)  A = JTAG port B = serial port.  We want to connect to the serial port.
 +
# Click on Port B, select properties and in the Advance tab ensure LOAD VCP is selected.
 +
# Unplug the device, and plug it back in.
 +
# Using PuTTY, connect to the COM port of "PORT B" and make sure the SPEED is set to 115200.
 +
# You might need to press ENTER  once or twice to get the prompt to actually show (sounds silly but it took me a while to figure that out lol).
 +
# Login using the default authentication information (username = root ) (password = nosoup4u)
  
 
[http://openplug.org/plugwiki/index.php/SerialTerminal/Windows/PuTTY Another HOW-TO for connecting to the SheevaPlug]
 
[http://openplug.org/plugwiki/index.php/SerialTerminal/Windows/PuTTY Another HOW-TO for connecting to the SheevaPlug]
  
 +
= Installing F12 on an SD =
  
−
== '''Installing F12 on an SD''' ==
+
# Plug an ethernet cable into the SheevaPlug and connect it to your router.
 +
# Check the DHCP table on the router to find out the IP that was assigned to the SheevaPlug (i.e. 192.168.15.109)
 +
# <code>ssh root@''ipaddress''</code> (i.e. 192.168.15.109)
 +
# Insert the SD card into the SheevaPlug's card reader slot.
 +
# <code>dmesg | tail</code> (shows the mount point) (i.e. /dev/mmc1)
 +
# Partition the SD card using <code>fdisk /dev/mmc1</code> (Delete any existing partitions)
 +
# Create a new partition (C) accept the defaults, make it bootable (a), verify it (p) and write the new partition table (w)
 +
# Create the file system using mkfs.ext3 /dev/mmc1
 +
# Get the Kernel: <code>wget http://ftp.linux.org.uk/pub/linux/arm/fedora/platforms/sheevaplug/uImage-2.6.30-sheevaplug</code> and root filesystem <code>http://ftp.linux.org.uk/pub/linux/arm/fedora/rootfs/rootfs-f12.tar.bz2</code>
 +
#*NOTE: WGET may not be installed on the SheevaPlug so run "yum install wget"
 +
#*NOTE: If you are not connected to the internet run route add default gw <ip address> and add the name server to /etc/resolv.conf
 +
# Create a mount point using <code>mkdir /media/flash</code>.  Mount the SD card using <code>/dev/mmc1 /media/flash</code>. Uncompress the file system using <code>tar -jxf rootfs-f12.tar.bz2</code>.  Copy the filesystem over to the SD card using <code>cp -r rootfs-f12/* /media/flash</code>. Copy the the kernel over to the SD card using <code>cp uImage-2.6.30-sheevaplug/media/flash/boot</code>
  
−
 
+
= Booting F12(on the SD) from SheevaPlug =
−
Step 1: Plug an ethernet cable into the SheevaPlug and connect it to your router.
 
−
 
 
−
Step 2: Check the DHCP table on the router to find out the IP that was assigned to the SheevaPlug (i.e. 192.168.15.109)
 
−
 
 
−
Step 3: SSH root@<ip address> (i.e. 192.168.15.109)
 
−
 
 
−
Step 4: Insert the SD card into the SheevaPlug's card reader slot.
 
−
 
 
−
Step 5: dmesg | tail (shows the mount point) (i.e. /dev/mmc1)
 
−
 
 
−
Step 6: Partition the SD card using fdisk /dev/mmc1 (Delete any existing partitions)
 
−
 
 
−
Step 7: Create a new partition (C) accept the defaults, make it bootable (a), verify it (p) and write the new partition table (w)
 
−
 
 
−
Step 8: Create the file system using mkfs.ext3 /dev/mmc1
 
−
 
 
−
Step 9: Get the Kernel wget http://ftp.linux.org.uk/pub/linux/arm/fedora/platforms/sheevaplug/uImage-2.6.30-sheevaplug and Distro http://ftp.linux.org.uk/pub/linux/arm/fedora/rootfs/rootfs-f12.tar.bz2
 
−
 
 
−
*NOTE: WGET may not be installed on the SheevaPlug so run "yum install wget"
 
−
**NOTE: If you are not connected to the internet run route add default gw <ip address> and add the name server to /etc/resolv.conf
 
−
 
 
−
Step 10: Create a mount point using mkdir /media/flash.  Mount the SD card using /dev/mmc1 /media/flash.  Uncompress the file system using tar -jxf rootfs-f12.tar.bz2.  Copy the filesystem over to the SD card using cp -r rootfs-f12/* /media/flash. Copy the the kernel over to the SD card using cp uImage-2.6.30-sheevaplug/media/flash/boot
 
−
 
 
−
 
 
−
== '''Booting F12(on the SD) from SheevaPlug''' ==
 
  
 
In order boot from the SD card, u-boot must be configured.  Depending on what version of u-boot you have, you might have to take an extra step in upgrading u-boot.  Use the link below for the upgrade procedures.
 
In order boot from the SD card, u-boot must be configured.  Depending on what version of u-boot you have, you might have to take an extra step in upgrading u-boot.  Use the link below for the upgrade procedures.
Line 103: Line 72:
 
If you have the newest version or have finished upgrading continue to the following steps:
 
If you have the newest version or have finished upgrading continue to the following steps:
  
−
Step 1: Reboot the SheevaPlug, and during the countdown, interrupt it by pressing any key.
+
# Reboot the SheevaPlug, and during the countdown, interrupt it by pressing any key.
−
 
+
# Run the following commands:
−
Step 2: Run the following commands:
+
#* Marvell>> setenv mainlineLinux yes
−
 
+
#* Marvell>> setenv arcNumber 2097
−
* Marvell>> setenv mainlineLinux yes
+
#* Marvell>> setenv bootargs_console console=ttyS0,115200
−
* Marvell>> setenv arcNumber 2097
+
#* Marvell>> setenv bootargs_root 'rw root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext2'
−
* Marvell>> setenv bootargs_console console=ttyS0,115200
+
#* Marvell>> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0 0x800000 /boot/uImage-2.6.30-sheevaplug'
−
* Marvell>> setenv bootargs_root 'rw root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext2'
+
#* Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) $(bootargs_root); run bootcmd_mmc; bootm 0x0800000'
−
* Marvell>> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0 0x800000 /boot/uImage-2.6.30-sheevaplug'
+
#* Marvell>> saveenv
−
* Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) $(bootargs_root); run bootcmd_mmc; bootm 0x0800000'
+
#* Marvell>> reset
−
* Marvell>> saveenv
+
# Once the device reboots, you should be prompted with the fedora-arm login.  Login using "root" and the password is "fedoraarm"
−
* Marvell>> reset
 
−
 
 
−
Step 3: Once the device reboots, you should be prompted with the fedora-arm login.  Login using "root" and the password is "fedoraarm"
 

Revision as of 16:39, 17 April 2010

Goal

To prepare the SheevaPlug, one of the ARM systems, so that it can be added to the Koji build pool.

SheevaPlug Specifications

Sheeva CPU Core

  • 1.2 GHz operation
  • L1 Cache: 16K Instruction + 16K Data
  • L2 Cache: 256KB

Memory

  • DDR2 400MHz, 16-bit bus, 512MB
  • NAND FLASH Controller, 8-bit bus, 512MB NAND FLASH
  • 128-bit eFuse Memory (for tiny, permanent storage, e.g., serial number)

Power

  • Power input: 100-240VAC/50-60Hz 19W DC Consumption: 5V/3.0A
  • High efficiency POL DC-DC converters

Development Interface

  • System Development Board JTAG and Console Interface via USB
  • SDIO expansion
  • JTAG OpenOCD support via USB

High Speed I/O & Peripherals

  • USB 2.0 Host
  • SD slot
  • RTC w/ Battery
  • Programmable LED

Hardware Links

Accessing SheevaPlug from a Windows 7 box

  1. Connect the device using the mini USB -> USB cable.
  2. Chances are Windows will struggle to find drivers for the device so just use the SheevaPlug_Host_SWsupportPackageWindowsHost.zip file that is included in the DevKit CD. Unzip it and use Device Manager to browse for the TeraTerm Drivers (located as a sub directory in the zip file you just extracted).
  3. Windows will find 2 devices (USB Converter A and B) A = JTAG port B = serial port. We want to connect to the serial port.
  4. Click on Port B, select properties and in the Advance tab ensure LOAD VCP is selected.
  5. Unplug the device, and plug it back in.
  6. Using PuTTY, connect to the COM port of "PORT B" and make sure the SPEED is set to 115200.
  7. You might need to press ENTER once or twice to get the prompt to actually show (sounds silly but it took me a while to figure that out lol).
  8. Login using the default authentication information (username = root ) (password = nosoup4u)

Another HOW-TO for connecting to the SheevaPlug

Installing F12 on an SD

  1. Plug an ethernet cable into the SheevaPlug and connect it to your router.
  2. Check the DHCP table on the router to find out the IP that was assigned to the SheevaPlug (i.e. 192.168.15.109)
  3. ssh root@ipaddress (i.e. 192.168.15.109)
  4. Insert the SD card into the SheevaPlug's card reader slot.
  5. dmesg | tail (shows the mount point) (i.e. /dev/mmc1)
  6. Partition the SD card using fdisk /dev/mmc1 (Delete any existing partitions)
  7. Create a new partition (C) accept the defaults, make it bootable (a), verify it (p) and write the new partition table (w)
  8. Create the file system using mkfs.ext3 /dev/mmc1
  9. Get the Kernel: wget http://ftp.linux.org.uk/pub/linux/arm/fedora/platforms/sheevaplug/uImage-2.6.30-sheevaplug and root filesystem http://ftp.linux.org.uk/pub/linux/arm/fedora/rootfs/rootfs-f12.tar.bz2
    • NOTE: WGET may not be installed on the SheevaPlug so run "yum install wget"
    • NOTE: If you are not connected to the internet run route add default gw <ip address> and add the name server to /etc/resolv.conf
  10. Create a mount point using mkdir /media/flash. Mount the SD card using /dev/mmc1 /media/flash. Uncompress the file system using tar -jxf rootfs-f12.tar.bz2. Copy the filesystem over to the SD card using cp -r rootfs-f12/* /media/flash. Copy the the kernel over to the SD card using cp uImage-2.6.30-sheevaplug/media/flash/boot

Booting F12(on the SD) from SheevaPlug

In order boot from the SD card, u-boot must be configured. Depending on what version of u-boot you have, you might have to take an extra step in upgrading u-boot. Use the link below for the upgrade procedures.

[How-TO on Upgrading U-Boot]

If you have the newest version or have finished upgrading continue to the following steps:

  1. Reboot the SheevaPlug, and during the countdown, interrupt it by pressing any key.
  2. Run the following commands:
    • Marvell>> setenv mainlineLinux yes
    • Marvell>> setenv arcNumber 2097
    • Marvell>> setenv bootargs_console console=ttyS0,115200
    • Marvell>> setenv bootargs_root 'rw root=/dev/mmcblk0p1 rootdelay=10 rootfstype=ext2'
    • Marvell>> setenv bootcmd_mmc 'mmcinit; ext2load mmc 0 0x800000 /boot/uImage-2.6.30-sheevaplug'
    • Marvell>> setenv bootcmd 'setenv bootargs $(bootargs_console) $(bootargs_root); run bootcmd_mmc; bootm 0x0800000'
    • Marvell>> saveenv
    • Marvell>> reset
  3. Once the device reboots, you should be prompted with the fedora-arm login. Login using "root" and the password is "fedoraarm"
Retrieved from "https://wiki.cdot.senecapolytechnic.ca/w/index.php?title=Fedora_ARM_Secondary_Architecture/SheevaPlug&oldid=38440"