Difference between revisions of "Cyclades Terminal Server"

From CDOT Wiki
Jump to: navigation, search
Line 51: Line 51:
 
[[Image:Acs32.png|thumb|widthpx| ]]
 
[[Image:Acs32.png|thumb|widthpx| ]]
  
Testing of the Cyclades ACS32 involved crossing the RX and TX of two [DB9 to RJ45] converters (which are in turn connected to cat5 cables between the converter and the port on the Cyclades). This is done by connecting pin 2 of connector A to pin 3 of connector 3, and vice versa.
+
Testing of the Cyclades ACS32 involved crossing the RX and TX of two [DB9 to RJ45] converters [which are in turn connected via CAT5 (or better) cables between the converter and the port on the Cyclades]. This is done by connecting pin 2 of connector A to pin 3 of connector B, and vice versa.
 
The ports on the Cyclades are then configured to accept SSH connection, and enabled.
 
The ports on the Cyclades are then configured to accept SSH connection, and enabled.
Make sure the ports are assigned the correct privilege group to connect to them, and ssh to them in the fashion shown on the enclosed PNG.
+
Make sure the ports are assigned the correct privilege user/group to connect to them, and ssh to them in the fashion shown on the PNG to the right -> .
  
 
Result: What you type in the SSH connection of one session, should appear on the ssh session of the corresponding port connected by the crossover cable. After testing that all ports can transmit and receive properly, one can conclude that the ports seem to be in working order.
 
Result: What you type in the SSH connection of one session, should appear on the ssh session of the corresponding port connected by the crossover cable. After testing that all ports can transmit and receive properly, one can conclude that the ports seem to be in working order.

Revision as of 12:13, 26 March 2015

The EHL is equipped with a Avocent Cyclades 32-port terminal server for access to the console port on specific development systems.

What is a Terminal Server?

A terminal server provides TCP/IP connectivity to RS-232 serial ports. Effectively, it lets you communicate with a serial port from anywhere on the Internet.

While this can be used for access to serial devices such as measurement tools and printers, or to enable a dedicated terminal to communicate with a network host, the terminal server in the EHL is used in a different way: it permits remote access to the serial console ports on computers within the EHL.

Most system firmware, boot software, and Linux kernels provide a console user interface. Only after the system is fully booted do network services become active.

On a PC, the console is often provided through a local video connection. On hyperscale system, it may be provided by an IPMI serial-over-LAN (SOL) connection. On a development board, it is usually provided by an RS-232 (or RS-485 or TTL) serial connection, and it is for this type of connection that a terminal server is used.

The EHL Terminal Server

The EHL terminal server is accessed through iraq.proximity.on.ca and has the local hostname "terminal".

Web Access

Web access to the terminal server permits you to configure a port for access, including the communication details (speed, word length, parity) and port security. Access http://terminal/ from Iraq.

The web interface also provides a Java-applet-based client for port access, but it is usually better to ssh directly to the port (below).

SSH Access

SSH access is the easiest and best way to access console ports connected to the terminal server.

SSH to the terminal server using the user ID username:port where username is your username on the terminal server and port is 7000 + serial port number. For example, to connect to serial port 3 with the Cyclades username "ostep", issue this command on Iraq:

ssh ostep:7003@terminal

To install your SSH key on the terminal server:

ssh-copy-id ostep@terminal

Use of the serial Script

The serial script (/usr/local/bin/serial on morocco and directly-connected VPN systems) lets you connect to a serial port by hostname, e.g.:

serial blue
serial x12
serial s1

Wiring

The Cyclades terminal server is connected to device serial ports using RJ-45 straight-through (not crossover) cables. These are connected directly to the Cyclades unit on one end, and to adapters (RJ-45f to DB-9f or RJ-45f to DB-25f) on the other end.

Stop (medium size).png
Do not connect Ethernet and Serial ports
Ethernet and serial connections in the EHL both use RJ-45 cables. Never connect the two, because they use incompatible voltage levels and signaling. RED cables must be used for serial connections and for nothing else; only non-RED cables shall be used for ethernet connections.

Testing

Acs32.png

Testing of the Cyclades ACS32 involved crossing the RX and TX of two [DB9 to RJ45] converters [which are in turn connected via CAT5 (or better) cables between the converter and the port on the Cyclades]. This is done by connecting pin 2 of connector A to pin 3 of connector B, and vice versa. The ports on the Cyclades are then configured to accept SSH connection, and enabled. Make sure the ports are assigned the correct privilege user/group to connect to them, and ssh to them in the fashion shown on the PNG to the right -> .

Result: What you type in the SSH connection of one session, should appear on the ssh session of the corresponding port connected by the crossover cable. After testing that all ports can transmit and receive properly, one can conclude that the ports seem to be in working order.